All the channels in the high-speed output module are set to the general purpose output mode (normal digital output) by d

As an alternative, you can combine hardware and software functions. (1) Hardware_ Prepare a relay output card and use

Proportional band P is the % of the variation range of input PV required for the change of output MV in the effective va

This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of

The equivalent data is retained for one default task during switching and the standby CPU starts execution from the begi

Do not install an I/O terminal (Type_NR1S*-*, NR1T*-*, NR1J*-*, and NR1D*-*) on the floor of the panel because it has no

The general-purpose communication function of Ethernet allows simplified broadcast communication. By using a CPU with b

Refer to 'Appendix 3-2 Procedure for Changing Resource (CPU type)' in the User's Manual 'Instructions' (FEH200 with inde

The MICREX-SX series positioning module 'Type_NP1F-HD2A' replaces NC1F-VP1/FGU130B. Be aware of the following points:

The Loader command mode is fixed to the TCP/IP communication. UDP/IP communication is not supported.

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

111-120 of Total 235

≪ 12 / 24page ≫

How do I perform pulse output with the high-speed output module (Type_NP1Y32T09P1-A)?

All the channels in the high-speed output module are set to the general purpose output mode (normal digital output) by default. To use the module in the pul... Show Detail
- No：1613
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:59
- Category： Function
The SPH does not have a RUN contact. Is there any alternative?

As an alternative, you can combine hardware and software functions. (1) Hardware_ Prepare a relay output card and use one point as a RUN contact. 　(2) Sof... Show Detail
- No：1587
- Displayed Date：2023/04/25 19:00
- Category： Main unit
In PPID, a POU for the PID FB package, which range does the % of proportional band P account for?

Proportional band P is the % of the variation range of input PV required for the change of output MV in the effective variation range from 0 to 100%. It is... Show Detail
- No：1580
- Displayed Date：2023/04/25 19:00
- Category： Function
Although the LED for ±OT lights up on the positioning control module (Type_ NP1F-MP2/MA2), the positioning operation finishes. What is the causal f...

This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of the positioning control module (Type_... Show Detail
- No：1575
- Displayed Date：2023/04/25 19:00
- Category： Function
How does the redundant system handle tasks being executed when the operation is switched from an operating CPU to a standby CPU?

The equivalent data is retained for one default task during switching and the standby CPU starts execution from the beginning of the task. Show Detail
- No：1530
- Displayed Date：2023/04/25 19:00
- Category： Main unit
Can I install an I/O terminal (Type_NR1S*-*, NR1T*-*, NR1J*-*, and NR1D*-*) in the vertical direction on the panel?

Do not install an I/O terminal (Type_NR1S*-*, NR1T*-*, NR1J*-*, and NR1D*-*) on the floor of the panel because it has no ventilation slit for cooling. You ca... Show Detail
- No：1520
- Displayed Date：2023/04/25 19:00
- Category： I/O
Can I perform broadcast communication between CPU modules without using FL-net or P/PE-link module?

The general-purpose communication function of Ethernet allows simplified broadcast communication. By using a CPU with built-in Ethernet, you can build a bro... Show Detail
- No：1485
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
How can I change the CPU type in an already created project?

Refer to 'Appendix 3-2 Procedure for Changing Resource (CPU type)' in the User's Manual 'Instructions' (FEH200 with index 'o' or later). Show Detail
- No：1467
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
I use the MICREX-F series positioning module (Type_NC1F-VP1/FGU130B). What replaces it? Is there anything to be aware of when replacing it?

The MICREX-SX series positioning module 'Type_NP1F-HD2A' replaces NC1F-VP1/FGU130B. Be aware of the following points: 1) NP1F-HD2A is differential output t... Show Detail
- No：1463
- Displayed Date：2023/04/25 19:00
- Category： Function
I use the Ethernet module (Type_ NP1L-ET1/ET2) in the Loader command mode. Can I also use the UDP/IP communication?

The Loader command mode is fixed to the TCP/IP communication. UDP/IP communication is not supported. Show Detail
- No：1442
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)