-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- <TELLUS-Remote> Are macro commands on the TELLUS remote screens executed?
- <TELLUS and V-Server> What is "licencing"?
- Though a monitored device is updated from V-Server, the version number the monitored device goes down.
- I want to use alarm monitoring function on V-Server, but the option [Alarm Monitor Setting] is inactive.
- <TELLUS-Remote> I want to synchronize the TELLUS remote screens and the monitored device.
Search by category
Keyword Search
FAQ within [ HMI ]
-
Cannot make entries with a keypad.
There is no entry target (no cursor is displayed). Entered valued is out of preset alarm lange. (the ENT key is not valid) The bit (Bit 15) for enabling/di... Show Detail
- No：4579
- Displayed Date：2025/12/01 13:47
- Category： Operation Troubles
-
How to check the number of the screen currently displayed
The currently displayed screen number is stored in the following device memory areas. Screen displaying device memory Device memory "n+2" in [Write Area] ... Show Detail
- No：4600
- Displayed Date：2025/12/01 13:49
- Updated DTM：2025/12/08 16:34
- Category： Questions about
-
How to specify the number of the initial screen upon powering-on
Specify the initial screen number on [Control Area] Setting location: [System Setting] > [Hardware Setting] > [Control Area] [When the initial scre... Show Detail
- No：4607
- Displayed Date：2025/12/01 13:49
- Category： Questions about
-
How to provide a numerical data entry feature using a keypad
Follow the steps below. [To call a numeric keypad when an entry target is pressed] Operation example Pressing on a numerical data display part brings up... Show Detail
- No：4626
- Displayed Date：2025/12/01 13:48
- Updated DTM：2025/12/08 19:03
- Category： Questions about
-
I want to use a tablet PC to monitor and operate V10/V9 screens.
VNC server function provides both. System configuration: Tablet PC : VNC client V10/V9F VNC server e.g. Follow the steps below to connect. 1. I... Show Detail
- No：4646
- Displayed Date：2025/12/01 13:48
- Category： Questions about
-
I want to disconnect my VNC client from the V10/V9.
You can disconnect the VNC client by one of two methods: Call the status bar on the bottom right corner of the screen. ■ For Advanced models: Pressany tw... Show Detail
- No：4647
- Displayed Date：2025/12/01 13:48
- Category： Questions about
-
This error may be displayed on the configuration software V-SFT when data is transferred. Possible causes and solutions are given below. [When the transf... Show Detail
- No：4718
- Displayed Date：2025/12/01 13:50
- Category： Error
-
Communication between the temperature controller and the V series is slow (V7 series).
To speed up communications, try the following method. The condition can also be improved as described below. <Baud rate> Increase the communicatio... Show Detail
- No：4727
- Displayed Date：2025/12/01 13:51
- Category： Operation Troubles
-
Negative values or decimal fractions cannot be entered with a keypad.
[Negative values cannot be entered] <Causes> Wrong operation of the keypad. The display type of entry target is set as "no sign". <Solutions... Show Detail
- No：4739
- Displayed Date：2025/12/01 13:49
- Category： Operation Troubles
-
Graphics do not move on an animated screen (in graphic or graphic relay mode).
The causes and solutions are explained for cases where the following parts are used. TS/V8 Graphic V7 Series Graphic Relay Graphic <Causes> Pa... Show Detail
- No：4743
- Displayed Date：2025/12/01 13:51
- Category： Operation Troubles
151-160 of Total 315