-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- Pressing the touch switch activates nothing or activates a position that deviates from the switch.
- Pressing a switch does not activate anything.
- When a screen with an overlap display is switched to another and is switched back, the overlap part disappears.
- Overlap editing is disabled.
- The POWER LED does not light up or flashes.
GLOBAL
Search by category
Keyword Search
FAQ within [ Operation Troubles ]
-
Ladder transfer cannot be performed properly.
The solution varies depending on the connection method between the PC and the V10/V9 series. There are three connection methods: USB, Ethernet, and serial (... Show Detail
- No：4589
- Displayed Date：2025/12/01 13:47
- Updated DTM：2025/12/08 12:29
-
This is a message that appears whendownloading and saving a file due to the security features of Microsoft Edge. Please follow the instructions below to dow... Show Detail
- No：4683
- Displayed Date：2025/12/01 13:47
- Updated DTM：2026/06/01 15:41
-
The POWER LED does not light up or flashes.
[The LED does not light up] <Causes> Power to the V series is not supplied properly. The LED is faulty (normal screen display). MONITOUCH is faulty... Show Detail
- No：4571
- Displayed Date：2025/12/01 13:47
-
The time and date is not displayed correctly.
The solutions vary depending on the screen data settings. Check the following settings. Setting location: V-SFT editor [System Setting]→[Unit Setting]→[... Show Detail
- No：4588
- Displayed Date：2025/12/01 13:47
- Updated DTM：2025/12/11 12:53
-
I want to show a multi-overlap using macro command but the overlap does not appear.
Check the following points: <Causes> Multi-overlap (icon) is not place on the screen. Multi-overlap setting (icon) is not correct. Macro command... Show Detail
- No：4593
- Displayed Date：2025/12/01 13:47
-
Two methods are available for editing. [Method 1: Select the overlap part] Select the overlap part. The overlap part is enclosed with handles. Selec... Show Detail
- No：4573
- Displayed Date：2025/12/01 13:47
-
Pressing a switch does not activate anything.
<Causes> Interlock is set for the switch. Touch switch position is not aligned. When using a switch for changing screens (Function: Screen Change-ov... Show Detail
- No：4575
- Displayed Date：2025/12/01 13:47
-
<Cause> When a control device memory bit is used to display a normal overlap or call-overlap part, only the leading edge (OFF -> ON) is recognized.... Show Detail
- No：4574
- Displayed Date：2025/12/01 13:47
- Updated DTM：2025/12/08 11:58
-
The V series does not switch from the RUN screen to Local mode.
Click here for the method for switching to Local mode. [If the switch menu is not displayed when the [SYSTEM] switch is pressed] <Cause> Advanced ... Show Detail
- No：4572
- Displayed Date：2025/12/01 13:47
-
I do not want to show a status bar on the bottom right corner of V series screen.
You can hide the status bar in the following way. Method 1: Click [x] on the status bar to temporarily hide it. Method 2: Use "Status Bar Prohibited" setti... Show Detail
- No：4662
- Displayed Date：2025/12/01 13:47
1-10 of Total 28