-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- How to sound a continuous buzzer according to a command from the PLC (external)
- How to make the screen dark when it is left untouched for a preset time
- How to overlay one switch on another on the screen
- How to hide overlap parts from the screen while editing the base screen
- How to display overlap parts from the PLC (external)
GLOBAL
Search by category
Keyword Search
FAQ within [ Questions about ]
-
How to shorten screen data transfer time (with screen data transfer cable: V-CP (serial connection))
The following methods are available. [Increase the baud rate] Select [Transfer]→[Communication Setting] or [Transfer]→[Download]→[Communication Setting] an... Show Detail
- No：4785
- Displayed Date：2025/12/01 13:49
-
How to save sampling data even after turning off the TS/V series
Select [SRAM] or [Storage/CF Card] for the storage location of sampling data. With [SRAM] selected, backup power is supplied from the battery attached to th... Show Detail
- No：4772
- Displayed Date：2025/12/01 13:51
- Updated DTM：2025/12/08 12:35
-
How to overlay one switch on another on the screen
As a rule, when placing switches, do not overlay one switch on another. When switches are overlaid, the switch placed first is valid. Other switches which ... Show Detail
- No：4764
- Displayed Date：2025/12/01 13:52
-
How to sound a continuous buzzer according to a command from the PLC (external)
Configure settings as follows. Select [System Setting] → [Unit Setting] → [General Settings] on the V-SFT editor and check [Use Continuous Buzzer Sound]. ... Show Detail
- No：4756
- Displayed Date：2025/12/01 13:52
-
How to make a switch work only when the switch is held down
Follow the steps below. * If you are using the V-SFT-6, see here. [V8/TS series] Display the [Switch] dialog, select [Delay] and set for [ON delay] (uni... Show Detail
- No：4793
- Displayed Date：2025/12/01 13:50
- Updated DTM：2025/12/11 14:46
-
How to replace a discontinued V/GD series unit with a V8/TS series unit
The V7/V6/V4 series and GD-80 series can be replaced with the V8/TS series. Note that, however, the compatibility is not 100% and some restrictions or limit... Show Detail
- No：4787
- Displayed Date：2025/12/01 13:49
-
How to set (correct) the calendar
The correction method differs depending on the calendar reading target (PLC or V/TS). For the reading target, check the following setting. Setting locati... Show Detail
- No：4779
- Displayed Date：2025/12/01 13:51
- Updated DTM：2025/12/08 12:25
-
How to designate entry targets in which data can be entered
Use the [Input Cursor Movement Device]. The [Input Cursor Movement Device] indicates the memory that controls whether to move the cursor to respective numer... Show Detail
- No：4769
- Displayed Date：2025/12/01 13:49
-
Follow the steps below. Select [View] → [Display Environment] → [Display] tab window, and check [Display Device]. (Setting can be made by selecting the rig... Show Detail
- No：4759
- Displayed Date：2025/12/01 13:52
-
How to provide a numerical data entry feature using a keypad
Follow the steps below. * If you are using the V-SFT-6, see here. [To call a numeric keypad when an entry target is pressed] * In the case of models ear... Show Detail
- No：4794
- Displayed Date：2025/12/01 13:50
- Updated DTM：2025/12/11 14:53
21-30 of Total 42