-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- Previous numeric data or characters remain in a numerical data display or character display part.
- The lamp lights up even though the bit in the lamp device memory is not ON.
- Switches cannot be placed in arbitrary positions.
- Pressing a switch does not activate anything.
- When a screen with an overlap display is switched to another and is switched back, the overlap part disappears.
GLOBAL
Search by category
Keyword Search
FAQ within [ Operation Troubles ]
-
The screen is not switched according to the command from the PLC (external).
The causes are listed below. <Causes> The screen number to display is not specified in read area "n + 2". The specified screen number is the same as... Show Detail
- No：4731
- Displayed Date：2025/12/01 13:51
-
MONITOUCH does not switch from the RUN screen to the Main Menu screen.
Press the [SYSTEM] switch, and when the switch menu is displayed press the [F1] (MODE) switch. [If the switch menu is not displayed when the [SYSTEM] sw... Show Detail
- No：4730
- Displayed Date：2025/12/01 13:51
- Updated DTM：2025/12/08 13:13
-
The POWER LED does not light up or flashes.
[The LED does not light up] <Causes> Power to the V/TS2060 series is not supplied properly. The LED is faulty (normal screen display). MONITOUCH is... Show Detail
- No：4729
- Displayed Date：2025/12/01 13:51
-
The Card Format switch (SRAM format) is not effective when pressed.
<Causes> The set word count for [Memory Card Emulation Area] is too small. There is no memory card mode icon. <Solutions> Select [System ... Show Detail
- No：4749
- Displayed Date：2025/12/01 13:51
-
Vertical lines are drawn in the trend sampling area but disappear.
<Cause> A drawing item (line) is placed in the trend sampling area. Drawing items must not be placed over the area. <Solution> TS/V8 ... Show Detail
- No：4746
- Displayed Date：2025/12/01 13:51
-
Transparency of a pattern is not effective on an animated screen.
<Cause> The size of the pattern is greater than 4,088 dots. <Solution> The transparency setting is enabled for pattern sizes up to 4,088 dot... Show Detail
- No：4744
- Displayed Date：2025/12/01 13:51
-
Graphics do not move on an animated screen (in graphic or graphic relay mode).
The causes and solutions are explained for cases where the following parts are used. TS/V8 Graphic V7 Series Graphic Relay Graphic <Causes> Pa... Show Detail
- No：4743
- Displayed Date：2025/12/01 13:51
-
Trend graphs cannot be displayed.
<Causes> No data is stored in the device memory address for each graph number. The number of points to display is not specified in the control device... Show Detail
- No：4741
- Displayed Date：2025/12/01 13:51
-
Negative values or decimal fractions cannot be entered with a keypad.
[Negative values cannot be entered] <Causes> Wrong operation of the keypad. The display type of entry target is set as "no sign". <Solutions... Show Detail
- No：4739
- Displayed Date：2025/12/01 13:49
-
Previous numeric data or characters remain in a numerical data display or character display part.
<Causes> TS/V8/V7 series The number of parts with the [Transparent] or [Shadow] setting has exceeded the number available on one screen. V6 series... Show Detail
- No：4736
- Displayed Date：2025/12/01 13:51
21-30 of Total 30