-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- Previous numeric data or characters remain in a numerical data display or character display part.
- The lamp lights up even though the bit in the lamp device memory is not ON.
- Switches cannot be placed in arbitrary positions.
- Pressing a switch does not activate anything.
- When a screen with an overlap display is switched to another and is switched back, the overlap part disappears.
GLOBAL
Search by category
Keyword Search
FAQ within [ Operation Troubles ]
-
MONITOUCH does not switch from the RUN screen to the Main Menu screen.
Press the [SYSTEM] switch, and when the switch menu is displayed press the [F1] (MODE) switch. [If the switch menu is not displayed when the [SYSTEM] sw... Show Detail
- No：4730
- Displayed Date：2025/12/01 13:51
- Updated DTM：2025/12/08 13:13
-
Communication between the PLC and the V/TS series is slow.
To speed up communications, try the following method. [When creating screens] When creating screens, consider the following points to improve the communi... Show Detail
- No：4878
- Displayed Date：2025/12/01 13:49
- Updated DTM：2025/12/08 16:05
-
The Card Format switch (SRAM format) is not effective when pressed.
<Causes> The set word count for [Memory Card Emulation Area] is too small. There is no memory card mode icon. <Solutions> Select [System ... Show Detail
- No：4749
- Displayed Date：2025/12/01 13:51
-
I cannot make entries with a keypad.
<Causes> There is no entry mode icon (no cursor is displayed). The keypad ID number is different from the entry mode ID number (all keys in the keypa... Show Detail
- No：4738
- Displayed Date：2025/12/01 13:51
- Updated DTM：2025/12/08 13:09
-
Communication between the temperature controller and the V series is slow (V7 series).
To speed up communications, try the following method. The condition can also be improved as described below. <Baud rate> Increase the communicatio... Show Detail
- No：4727
- Displayed Date：2025/12/01 13:51
-
Three methods are available for editing. [Method 1: Select the overlap part] Select the overlap part. The overlap part is enclosed with handles. S... Show Detail
- No：4879
- Displayed Date：2025/12/01 13:49
-
The time and date is not displayed correctly.
The solutions vary depending on the screen data settings. Check the following settings. Setting location: V-SFT editor [System Setting]→[Unit Setting]→[SR... Show Detail
- No：4751
- Displayed Date：2025/12/01 13:51
- Updated DTM：2025/12/08 12:17
-
Previous numeric data or characters remain in a numerical data display or character display part.
<Causes> TS/V8/V7 series The number of parts with the [Transparent] or [Shadow] setting has exceeded the number available on one screen. V6 series... Show Detail
- No：4736
- Displayed Date：2025/12/01 13:51
-
The PLC memory address for a part is garbled as "??" or is "blank".
<Causes> When the PLC model setting is changed, it is replaced with device "??". PLC2 - 8 (Temperature Control/PLC2Way with the V7 series) are set as... Show Detail
- No：4754
- Displayed Date：2025/12/01 13:51
-
MONITOUCH does not recognize the storage dvice.
<Causes> The file system of the storage device is not supported. The CF card cover is open (V8 series only). The error status is set in $s497 (or $s... Show Detail
- No：4750
- Displayed Date：2025/12/01 13:51
11-20 of Total 30