-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- Previous numeric data or characters remain in a numerical data display or character display part.
- The lamp lights up even though the bit in the lamp device memory is not ON.
- Switches cannot be placed in arbitrary positions.
- Pressing a switch does not activate anything.
- When a screen with an overlap display is switched to another and is switched back, the overlap part disappears.
GLOBAL
Search by category
Keyword Search
FAQ within [ Operation Troubles ]
-
Graphics do not move on an animated screen (in graphic or graphic relay mode).
The causes and solutions are explained for cases where the following parts are used. TS/V8 Graphic V7 Series Graphic Relay Graphic <Causes> Pa... Show Detail
- No：4743
- Displayed Date：2025/12/01 13:51
-
In the alarm tracking display, alarm data is not tracked for the specified number of times.
<Cause> [Buffering Area Setting] → [Number of Data to Save] is small. <Solution> Increase the number set for [Number of Data to Save]. For ... Show Detail
- No：4748
- Displayed Date：2025/12/01 13:51
-
MONITOUCH does not recognize the storage dvice.
<Causes> The file system of the storage device is not supported. The CF card cover is open (V8 series only). The error status is set in $s497 (or $s... Show Detail
- No：4750
- Displayed Date：2025/12/01 13:51
-
MONITOUCH does not switch from the RUN screen to the Main Menu screen.
Press the [SYSTEM] switch, and when the switch menu is displayed press the [F1] (MODE) switch. [If the switch menu is not displayed when the [SYSTEM] sw... Show Detail
- No：4730
- Displayed Date：2025/12/01 13:51
- Updated DTM：2025/12/08 13:13
-
The data displayed in a trend graph is different from the most recent data in the PLC.
<Cause> The trend graph is not redrawn. <Solution> The graph data once displayed is not updated unless the redraw command is specified. To ... Show Detail
- No：4742
- Displayed Date：2025/12/01 13:51
-
Transparency of a pattern is not effective on an animated screen.
<Cause> The size of the pattern is greater than 4,088 dots. <Solution> The transparency setting is enabled for pattern sizes up to 4,088 dot... Show Detail
- No：4744
- Displayed Date：2025/12/01 13:51
-
Communication between the PLC and the V/TS series is slow.
To speed up communications, try the following method. [When creating screens] When creating screens, consider the following points to improve the communi... Show Detail
- No：4878
- Displayed Date：2025/12/01 13:49
- Updated DTM：2025/12/08 16:05
-
The screen is not switched according to the command from the PLC (external).
The causes are listed below. <Causes> The screen number to display is not specified in read area "n + 2". The specified screen number is the same as... Show Detail
- No：4731
- Displayed Date：2025/12/01 13:51
-
Messages are not displayed in the alarm tracking display.
<Causes> [Start Bit] for sampling control device memory is checked, but the bit is not ON. The reset bit for sampling control device memory is ON. T... Show Detail
- No：4745
- Displayed Date：2025/12/01 13:51
-
The POWER LED does not light up or flashes.
[The LED does not light up] <Causes> Power to the V/TS2060 series is not supplied properly. The LED is faulty (normal screen display). MONITOUCH is... Show Detail
- No：4729
- Displayed Date：2025/12/01 13:51
1-10 of Total 30