-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
GLOBAL
Search by category
Keyword Search
FAQ within [ V8/TS2060 series ]
-
How to draw reference lines in a trend graph or trend sampling part
V-SFT Ver.6 [To draw four or less horizontal reference lines] Display the [Trend Graph] dialog and click [Contents]. Check a [Reference Line] to use and se... Show Detail
- No：4771
- Displayed Date：2025/12/01 13:49
- Category： Questions about
-
The lamp lights up even though the bit in the lamp device memory is not ON.
<Cause> The lamp device memory is used redundantly. <Solution> Check if the same address as the lamp device memory is used in the screen dat... Show Detail
- No：4735
- Displayed Date：2025/12/01 13:51
- Category： Operation Troubles
-
MONITOUCH does not switch from the RUN screen to the Main Menu screen.
Press the [SYSTEM] switch, and when the switch menu is displayed press the [F1] (MODE) switch. [If the switch menu is not displayed when the [SYSTEM] sw... Show Detail
- No：4730
- Displayed Date：2025/12/01 13:51
- Updated DTM：2025/12/08 13:13
- Category： Operation Troubles
-
How to check the communication condition between the temperature controller and the V/TS
The temperature controller condition is output to the system device memory of the V/TS. Check the following addresses for each station number. [V8/TS] Sel... Show Detail
- No：4883
- Displayed Date：2025/12/01 13:50
- Updated DTM：2025/12/08 11:59
- Category： Questions about
-
Communication between the PLC and the V/TS series is slow.
To speed up communications, try the following method. [When creating screens] When creating screens, consider the following points to improve the communi... Show Detail
- No：4878
- Displayed Date：2025/12/01 13:49
- Updated DTM：2025/12/08 16:05
- Category： Operation Troubles
-
How to indicate battery trouble of the V/TS series on the PLC side
The condition of the battery in the V/TS series is output to system device memory $s167. For information about $s167, click here. The condition can be tran... Show Detail
- No：4789
- Displayed Date：2025/12/01 13:49
- Category： Questions about
-
How to shorten screen data transfer time (with screen data transfer cable: V-CP (serial connection))
The following methods are available. [Increase the baud rate] Select [Transfer]→[Communication Setting] or [Transfer]→[Download]→[Communication Setting] an... Show Detail
- No：4785
- Displayed Date：2025/12/01 13:49
- Category： Questions about
-
How to save sampling data even after turning off the TS/V series
Select [SRAM] or [Storage/CF Card] for the storage location of sampling data. With [SRAM] selected, backup power is supplied from the battery attached to th... Show Detail
- No：4772
- Displayed Date：2025/12/01 13:51
- Updated DTM：2025/12/08 12:35
- Category： Questions about
-
How to overlay one switch on another on the screen
As a rule, when placing switches, do not overlay one switch on another. When switches are overlaid, the switch placed first is valid. Other switches which ... Show Detail
- No：4764
- Displayed Date：2025/12/01 13:52
- Category： Questions about
-
How to sound a continuous buzzer according to a command from the PLC (external)
Configure settings as follows. Select [System Setting] → [Unit Setting] → [General Settings] on the V-SFT editor and check [Use Continuous Buzzer Sound]. ... Show Detail
- No：4756
- Displayed Date：2025/12/01 13:52
- Category： Questions about
51-60 of Total 106