-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
GLOBAL
Search by category
Keyword Search
FAQ within [ V8/TS2060 series ]
-
How to replace a discontinued V/GD series unit with a V8/TS series unit
The V7/V6/V4 series and GD-80 series can be replaced with the V8/TS series. Note that, however, the compatibility is not 100% and some restrictions or limit... Show Detail
- No：4787
- Displayed Date：2025/12/01 13:49
- Category： Questions about
-
How to make a switch work only when the switch is held down
Follow the steps below. * If you are using the V-SFT-6, see here. [V8/TS series] Display the [Switch] dialog, select [Delay] and set for [ON delay] (uni... Show Detail
- No：4793
- Displayed Date：2025/12/01 13:50
- Updated DTM：2025/12/11 14:46
- Category： Questions about
-
Three methods are available for editing. [Method 1: Select the overlap part] Select the overlap part. The overlap part is enclosed with handles. S... Show Detail
- No：4879
- Displayed Date：2025/12/01 13:49
- Category： Operation Troubles
-
Communication between the temperature controller and the V series is slow (V7 series).
To speed up communications, try the following method. The condition can also be improved as described below. <Baud rate> Increase the communicatio... Show Detail
- No：4727
- Displayed Date：2025/12/01 13:51
- Category： Operation Troubles
-
I cannot make entries with a keypad.
<Causes> There is no entry mode icon (no cursor is displayed). The keypad ID number is different from the entry mode ID number (all keys in the keypa... Show Detail
- No：4738
- Displayed Date：2025/12/01 13:51
- Updated DTM：2025/12/08 13:09
- Category： Operation Troubles
-
The Card Format switch (SRAM format) is not effective when pressed.
<Causes> The set word count for [Memory Card Emulation Area] is too small. There is no memory card mode icon. <Solutions> Select [System ... Show Detail
- No：4749
- Displayed Date：2025/12/01 13:51
- Category： Operation Troubles
-
How to sound a continuous buzzer according to a command from the PLC (external)
Configure settings as follows. Select [System Setting] → [Unit Setting] → [General Settings] on the V-SFT editor and check [Use Continuous Buzzer Sound]. ... Show Detail
- No：4756
- Displayed Date：2025/12/01 13:52
- Category： Questions about
-
How to overlay one switch on another on the screen
As a rule, when placing switches, do not overlay one switch on another. When switches are overlaid, the switch placed first is valid. Other switches which ... Show Detail
- No：4764
- Displayed Date：2025/12/01 13:52
- Category： Questions about
-
How to save sampling data even after turning off the TS/V series
Select [SRAM] or [Storage/CF Card] for the storage location of sampling data. With [SRAM] selected, backup power is supplied from the battery attached to th... Show Detail
- No：4772
- Displayed Date：2025/12/01 13:51
- Updated DTM：2025/12/08 12:35
- Category： Questions about
-
How to shorten screen data transfer time (with screen data transfer cable: V-CP (serial connection))
The following methods are available. [Increase the baud rate] Select [Transfer]→[Communication Setting] or [Transfer]→[Download]→[Communication Setting] an... Show Detail
- No：4785
- Displayed Date：2025/12/01 13:49
- Category： Questions about
41-50 of Total 106