-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
GLOBAL
Search by category
Keyword Search
FAQ within [ V8/TS2060 series ]
-
The PLC memory address for a part is garbled as "??" or is "blank".
<Causes> When the PLC model setting is changed, it is replaced with device "??". PLC2 - 8 (Temperature Control/PLC2Way with the V7 series) are set as... Show Detail
- No：4754
- Displayed Date：2025/12/01 13:51
- Category： Operation Troubles
-
How to draw reference lines in a trend graph or trend sampling part
V-SFT Ver.6 [To draw four or less horizontal reference lines] Display the [Trend Graph] dialog and click [Contents]. Check a [Reference Line] to use and se... Show Detail
- No：4771
- Displayed Date：2025/12/01 13:49
- Category： Questions about
-
MONITOUCH does not switch from the RUN screen to the Main Menu screen.
Press the [SYSTEM] switch, and when the switch menu is displayed press the [F1] (MODE) switch. [If the switch menu is not displayed when the [SYSTEM] sw... Show Detail
- No：4730
- Displayed Date：2025/12/01 13:51
- Updated DTM：2025/12/08 13:13
- Category： Operation Troubles
-
How to limit the values that can be entered through the keypad
Follow the steps below. Click on the numerical data display part (Function: Entry Target). Display the [Num. Display] dialog, select [Operation/Alarm] and c... Show Detail
- No：4768
- Displayed Date：2025/12/01 13:49
- Category： Questions about
-
How to connect to a temperature controller / inverter without connecting to a PLC
The method differs according to the TS/the V series model. TS/V8 series Select [System Setting]→[Hardware Setting]→[PLC1] on the V-SFT editor and configure... Show Detail
- No：4784
- Displayed Date：2025/12/01 13:49
- Category： Questions about
-
How to check the number of the screen currently displayed
The currently displayed screen number is stored in the following device memory areas. Device memory "n+2" in [Write Area] System device memory$s0 Writ... Show Detail
- No：4788
- Displayed Date：2025/12/01 13:49
- Category： Questions about
-
How to save sampling data even after turning off the TS/V series
Select [SRAM] or [Storage/CF Card] for the storage location of sampling data. With [SRAM] selected, backup power is supplied from the battery attached to th... Show Detail
- No：4772
- Displayed Date：2025/12/01 13:51
- Updated DTM：2025/12/08 12:35
- Category： Questions about
-
How to replace a discontinued V/GD series unit with a V8/TS series unit
The V7/V6/V4 series and GD-80 series can be replaced with the V8/TS series. Note that, however, the compatibility is not 100% and some restrictions or limit... Show Detail
- No：4787
- Displayed Date：2025/12/01 13:49
- Category： Questions about
-
This error may be displayed on the configuration software V-SFT when data is transferred. Possible causes and solutions are given below. [When the transf... Show Detail
- No：4877
- Displayed Date：2025/12/01 13:49
- Category： Error
-
How to check the communication condition between the temperature controller and the V/TS
The temperature controller condition is output to the system device memory of the V/TS. Check the following addresses for each station number. [V8/TS] Sel... Show Detail
- No：4883
- Displayed Date：2025/12/01 13:50
- Updated DTM：2025/12/08 11:59
- Category： Questions about
31-40 of Total 106