-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
GLOBAL
Search by category
Keyword Search
FAQ within [ V8/TS2060 series ]
-
The POWER LED does not light up or flashes.
[The LED does not light up] <Causes> Power to the V/TS2060 series is not supplied properly. The LED is faulty (normal screen display). MONITOUCH is... Show Detail
- No：4729
- Displayed Date：2025/12/01 13:51
- Category： Operation Troubles
-
MONITOUCH does not switch from the RUN screen to the Main Menu screen.
Press the [SYSTEM] switch, and when the switch menu is displayed press the [F1] (MODE) switch. [If the switch menu is not displayed when the [SYSTEM] sw... Show Detail
- No：4730
- Displayed Date：2025/12/01 13:51
- Updated DTM：2025/12/08 13:13
- Category： Operation Troubles
-
The screen is not switched according to the command from the PLC (external).
The causes are listed below. <Causes> The screen number to display is not specified in read area "n + 2". The specified screen number is the same as... Show Detail
- No：4731
- Displayed Date：2025/12/01 13:51
- Category： Operation Troubles
-
Pressing a switch does not activate anything.
<Causes> Interlock is set for the switch. ON delay is set for the switch. (TS/V8 only) Touch switch position is deviated. When the screen change sw... Show Detail
- No：4733
- Displayed Date：2025/12/01 13:51
- Category： Operation Troubles
-
The lamp lights up even though the bit in the lamp device memory is not ON.
<Cause> The lamp device memory is used redundantly. <Solution> Check if the same address as the lamp device memory is used in the screen dat... Show Detail
- No：4735
- Displayed Date：2025/12/01 13:51
- Category： Operation Troubles
-
I cannot make entries with a keypad.
<Causes> There is no entry mode icon (no cursor is displayed). The keypad ID number is different from the entry mode ID number (all keys in the keypa... Show Detail
- No：4738
- Displayed Date：2025/12/01 13:51
- Updated DTM：2025/12/08 13:09
- Category： Operation Troubles
-
When a character entry switch is pressed, the switch name on it disappears.
<Cause> The character entry key switch is set as [Draw Mode: REP]. <Solution> Set [Draw Mode: XOR]. When using characters from the graphic ... Show Detail
- No：4740
- Displayed Date：2025/12/01 13:49
- Updated DTM：2025/12/08 13:04
- Category： Operation Troubles
-
The data displayed in a trend graph is different from the most recent data in the PLC.
<Cause> The trend graph is not redrawn. <Solution> The graph data once displayed is not updated unless the redraw command is specified. To ... Show Detail
- No：4742
- Displayed Date：2025/12/01 13:51
- Category： Operation Troubles
-
Pressing the reset switch does not clear history data.
<Causes> The switch is not pressed twice. The switch function is not set to [Reset]. The switch is disabled according to the interlock setting. ... Show Detail
- No：4747
- Displayed Date：2025/12/01 13:51
- Category： Operation Troubles
-
How to display overlap parts from the PLC (external)
There are four overlap part types. Normal overlap Call-overlap Multi overlap Global overlap In the case of external commands, the display method diffe... Show Detail
- No：4761
- Displayed Date：2025/12/01 13:52
- Updated DTM：2025/12/08 12:43
- Category： Questions about
21-30 of Total 106