-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
GLOBAL
Search by category
Keyword Search
FAQ within [ V8/TS2060 series ]
-
How to shorten screen data transfer time (with screen data transfer cable: V-CP (serial connection))
The following methods are available. [Increase the baud rate] Select [Transfer]→[Communication Setting] or [Transfer]→[Download]→[Communication Setting] an... Show Detail
- No：4785
- Displayed Date：2025/12/01 13:49
- Category： Questions about
-
In the alarm tracking display, alarm data is not tracked for the specified number of times.
<Cause> [Buffering Area Setting] → [Number of Data to Save] is small. <Solution> Increase the number set for [Number of Data to Save]. For ... Show Detail
- No：4748
- Displayed Date：2025/12/01 13:51
- Category： Operation Troubles
-
How to copy a screen from one file to another
Three methods are available. Follow the steps below. [Method 1: Copy each item] Select [File] → [Comparing]. Enter filenames for [Comparison] (source) and... Show Detail
- No：4757
- Displayed Date：2025/12/01 13:52
- Category： Questions about
-
How to save sampling data to a CSV file
Two methods are available. Follow the steps below. [To output by setting] Select [System Setting] → [Buffering Area Setting] on the V-SFT editor and check ... Show Detail
- No：4773
- Displayed Date：2025/12/01 13:51
- Category： Questions about
-
How to read or write data between the PLC, temperature controller and inverter at regular intervals
Use [Device Memory Map Setting] . Periodic Reading Click [System Setting]→[Device Memory Map] → [PLCn].Select a device memory map number and click [OK]. ... Show Detail
- No：4782
- Displayed Date：2025/12/01 13:51
- Category： Questions about
-
"Editor is occupied by another port"
This error may be displayed on the configuration software V-SFT when data is transferred via Ethernet. Possible causes and solutions are given below. &... Show Detail
- No：4722
- Displayed Date：2025/12/01 13:50
- Category： Error
-
When a character entry switch is pressed, the switch name on it disappears.
<Cause> The character entry key switch is set as [Draw Mode: REP]. <Solution> Set [Draw Mode: XOR]. When using characters from the graphic ... Show Detail
- No：4740
- Displayed Date：2025/12/01 13:49
- Updated DTM：2025/12/08 13:04
- Category： Operation Troubles
-
Messages are not displayed in the alarm tracking display.
<Causes> [Start Bit] for sampling control device memory is checked, but the bit is not ON. The reset bit for sampling control device memory is ON. T... Show Detail
- No：4745
- Displayed Date：2025/12/01 13:51
- Category： Operation Troubles
-
How to set asynchronous display of multiple lines in a trend graph
Two or more trend graph parts in the same size must be overlaid. It is possible to display the trend lines at different timings by linking the parts with ea... Show Detail
- No：4770
- Displayed Date：2025/12/01 13:49
- Category： Questions about
-
How to set (correct) the calendar
The correction method differs depending on the calendar reading target (PLC or V/TS). For the reading target, check the following setting. Setting locati... Show Detail
- No：4779
- Displayed Date：2025/12/01 13:51
- Updated DTM：2025/12/08 12:25
- Category： Questions about
11-20 of Total 106