Yes, there are special models available without logos imprinted on the bezel. [Model details] Special models are designa

This error may be displayed on the configuration software V-SFT when data is transferred. Possible causes and solutions

When Fuji Electric MICREX-SX is selected, this error is displayed if screen data uses input/output memory (X, Y), or P l

<Cause> The lamp device memory is used redundantly. <Solution> Check if the same address as the lamp device

There is no entry target (no cursor is displayed). Entered valued is out of preset alarm lange. (the ENT key is not vali

Check the following points: <Causes> Multi-overlap (icon) is not place on the screen. Multi-overlap setting (ic

There are three methods. [Change the setting on V series] Switch to Local mode, select [System setting] > [Backlight

Use the [Device Memory Map] setting. Setting location: [System Setting] -> [Device Memory Map] [Reading temperature c

Two methods are available. [Method 1: When the model is included in the options in the [Hardware Setting] dialog] The V1

Yes. Set as shown below. Configure [PLC1] as a temperature controller at [System Setting] -> [Hardware Setting] on th

Font Size
S
M
L

GLOBAL > HMI > V10/V9 series

Latest FAQ

GLOBAL

Search by category

Keyword Search

FAQ within [ V10/V9 series ]

1-10 of Total 166

≪ 1 / 17page ≫

Are there any models without logos?

Yes, there are special models available without logos imprinted on the bezel. [Model details] Special models are designated with a number following the sta... Show Detail
- No：4538
- Displayed Date：2025/12/01 13:48
- Category： Product Specifications
"The size is too large to communicate."

This error may be displayed on the configuration software V-SFT when data is transferred. Possible causes and solutions are given below. <Cause> T... Show Detail
- No：4556
- Displayed Date：2025/12/01 13:47
- Category： Error
"Import file is not selected"

When Fuji Electric MICREX-SX is selected, this error is displayed if screen data uses input/output memory (X, Y), or P link/PE link/FL-net (CPU No. 8, 9) mem... Show Detail
- No：4558
- Displayed Date：2025/12/01 13:47
- Category： Error
The lamp lights up even though the bit in the lamp device memory is not ON (OFF).

<Cause> The lamp device memory is used redundantly. <Solution> Check if the same address as the lamp device memory is used in the screen data ... Show Detail
- No：4576
- Displayed Date：2025/12/01 13:47
- Category： Operation Troubles
Cannot make entries with a keypad.

There is no entry target (no cursor is displayed). Entered valued is out of preset alarm lange. (the ENT key is not valid) The bit (Bit 15) for enabling/di... Show Detail
- No：4579
- Displayed Date：2025/12/01 13:47
- Category： Operation Troubles
I want to show a multi-overlap using a button but the overlap does not appear.

Check the following points: <Causes> Multi-overlap (icon) is not place on the screen. Multi-overlap setting (icon) is not correct. Macro command... Show Detail
- No：4591
- Displayed Date：2025/12/01 13:47
- Category： Operation Troubles
How to change setting for the backlight

There are three methods. [Change the setting on V series] Switch to Local mode, select [System setting] > [Backlight setting] to make changes and press ... Show Detail
- No：4603
- Displayed Date：2025/12/01 13:49
- Category： Questions about
How to read or write data between the temperature controller/inverter and the PLC device memory or internal device memory at regular intervals

Use the [Device Memory Map] setting. Setting location: [System Setting] -> [Device Memory Map] [Reading temperature controller/inverter data at regular ... Show Detail
- No：4640
- Displayed Date：2025/12/01 13:48
- Category： Questions about
How to connect two temperature controllers/inverters from different manufacturers

Two methods are available. [Method 1: When the model is included in the options in the [Hardware Setting] dialog] The V10/V9 series can be connected with t... Show Detail
- No：4641
- Displayed Date：2025/12/01 13:48
- Category： Questions about
Can I connect V10/V9 only with a temperature controller without connecting any PLC?

Yes. Set as shown below. Configure [PLC1] as a temperature controller at [System Setting] -> [Hardware Setting] on the V-SFT editor. Show Detail
- No：4642
- Displayed Date：2025/12/01 13:48
- Category： Questions about

1-10 of Total 166

V10/V9 series

Available Devices

Info & News

To Top of Page

V10/V9 series

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability

Latest FAQ

GLOBAL

Search by category

Keyword Search

FAQ within [ V10/V9 series ]

V10/V9 series

Info & News