The minimum required products are (1) High-performance CPU exclusively for the electronic cam, (2) pulse train combine

The flashing of the LED of the high-speed output module (Type_ NP1Y32T09P1-A) indicates that pulse output is generated.

Check the following points_ (1) Check the input form specified on the application program. (2) Set Enable counting to

Since the parameter data area of the positioning control module (Type_ NP1F-MP2/MA2) operates on the RAM, it is always c

For setting parameter values (such as P, I and D), it is possible to_ (1) Set the data within the user application (2)

The four-axis pulse string output terminal module (Type_ NR1SF-HP4DT) does not have a physical ±OT terminal. You can s

Pulse output completion is indicated by the 'Command pulse zero' signal. Normally, it is '1' to indicate the status of

Both the pulse output and control output are open collector outputs. They should be used within the following ranges (1)

In the MV selection part in the PID FB, (1) the backward operation uses the internally calculated MV value (%) without p

If the start bit remains on, the positioning end signal is not generated.

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH > Function

Latest FAQ

When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
When I switch the CPU module from RUN to STOP while the four-axis pulse output unit (NR1SF-HP4DT) is outputting pulses, does the positioning operat...
With a counter module (NP1F-HC2), I use ２ counter FBs to control 2 channels. At system start-up, I set simultaneous preset operations for the 2 cha...
What is the difference between the PID forward and backward operations when the PID FB package is used?
How can I detect a low battery voltage of the SRAM card with the memory card interface module (Type_ NP1F-MM1)?

GLOBAL

Search by category

Keyword Search

FAQ within [ Function ]

1-10 of Total 50

≪ 1 / 5page ≫

Which devices are required for controlling an electronic cam with the SPH Series? What should I prepare?

The minimum required products are (1) High-performance CPU exclusively for the electronic cam, (2) pulse train combined module (Type_ NP1F-MP2) or anal... Show Detail
- No：1323
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:20
With the high-speed output module (Type_ NP1Y32T09P1-A), the LED flashes but no pulse is output to the outside. What should I check?

The flashing of the LED of the high-speed output module (Type_ NP1Y32T09P1-A) indicates that pulse output is generated. If no pulse output is generated in t... Show Detail
- No：1291
- Displayed Date：2023/04/25 19:00
Pulse counting is disabled on the high-speed input module (Type_ NP1X3206-A). What should I check?

Check the following points_ (1) Check the input form specified on the application program. (2) Set Enable counting to '1.' If the pulse count data regist... Show Detail
- No：1570
- Displayed Date：2023/04/25 19:00
When I turned on the positioning control module (Type_ NP1F-MP2/MA2) in the morning, the parameters were reset to the initial values. What is the f...

Since the parameter data area of the positioning control module (Type_ NP1F-MP2/MA2) operates on the RAM, it is always cleared when you turn off the module. ... Show Detail
- No：1573
- Displayed Date：2023/04/25 19:00
For PID control by using a PID FB package, how should I set the various parameters?

For setting parameter values (such as P, I and D), it is possible to_ (1) Set the data within the user application (2) Use 'PID FB parameter support ut... Show Detail
- No：1296
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:18
I want to connect wiring for ±OT input with the four-axis pulse string output terminal module (Type_ NR1SF-HP4DT) but the unit does not have the te...

The four-axis pulse string output terminal module (Type_ NR1SF-HP4DT) does not have a physical ±OT terminal. You can solve this problem by using software a... Show Detail
- No：1447
- Displayed Date：2023/04/25 19:00
Which is the signal that indicates pulse output completion on the positioning control module (Type_ NP1F-MP2)?

Pulse output completion is indicated by the 'Command pulse zero' signal. Normally, it is '1' to indicate the status of completion. When the number of pulses... Show Detail
- No：1548
- Displayed Date：2023/04/25 19:00
I use the pulse train output positioning control module (Type_ NP1F-HP2). Please tell me the rated voltage/current of the pulse output and control ...

Both the pulse output and control output are open collector outputs. They should be used within the following ranges (1) Pulse output_ 30 V DC, 40 mA or less... Show Detail
- No：1602
- Displayed Date：2023/04/25 19:00
What is the difference between the PID forward and backward operations when the PID FB package is used?

In the MV selection part in the PID FB, (1) the backward operation uses the internally calculated MV value (%) without processing it (as-is)_ and (2) the for... Show Detail
- No：1625
- Displayed Date：2023/04/25 19:00
With the pulse train output positioning control module (Type_ NP1F-HP2), positioning has ended but the end signal is not generated.

If the start bit remains on, the positioning end signal is not generated. Show Detail
- No：1317
- Displayed Date：2023/04/25 19:00