The MICREX-SX series positioning module 'Type_NP1F-HD2A' replaces NC1F-VP1/FGU130B. Be aware of the following points:

You cannot use software filters when you use the pulse counter input function of the high-speed input module (Type_ NP1X

Pulse input type_ A-phase for the pulse and B-phase for the sign.

Yes, all points can be used. Regarding the pulse width, pulse signals with a width down to 20 us can be captured with po

A possible cause is that a “Deviation amount over error” occurred. For details, refer to the user's manual FEH213 (NP1F-

All the channels in the high-speed output module are set to the general purpose output mode (normal digital output) by d

It seems that this problem was caused by an improper address setting for INDAT/OUTDAT assigned to the counter FB termina

While NP1F-HC2 requires an external power supply of 5 V DC, NP1F-HC8 produces 5 V DC within the module from an external

The counter is initially set to gate mode. Counting is disabled unless you provide a 'gate signal' externally by hardwar

Both the pulse output and control output are open collector outputs. They should be used within the following ranges (1)

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH > Function

Latest FAQ

When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
When I switch the CPU module from RUN to STOP while the four-axis pulse output unit (NR1SF-HP4DT) is outputting pulses, does the positioning operat...
With a counter module (NP1F-HC2), I use ２ counter FBs to control 2 channels. At system start-up, I set simultaneous preset operations for the 2 cha...
What is the difference between the PID forward and backward operations when the PID FB package is used?
How can I detect a low battery voltage of the SRAM card with the memory card interface module (Type_ NP1F-MM1)?

GLOBAL

Search by category

Keyword Search

FAQ within [ Function ]

21-30 of Total 50

≪ 3 / 5page ≫

I use the MICREX-F series positioning module (Type_NC1F-VP1/FGU130B). What replaces it? Is there anything to be aware of when replacing it?

The MICREX-SX series positioning module 'Type_NP1F-HD2A' replaces NC1F-VP1/FGU130B. Be aware of the following points: 1) NP1F-HD2A is differential output t... Show Detail
- No：1463
- Displayed Date：2023/04/25 19:00
When I use the pulse counter input function of the high-speed input module (Type_ NP1X3206-A), can I set software filters?

You cannot use software filters when you use the pulse counter input function of the high-speed input module (Type_ NP1X3206-A). Show Detail
- No：1599
- Displayed Date：2023/04/25 19:00
With the multi-channel high-speed counter module (Type_ NP1F-HC8), how can a single-phase pulse be received?

Pulse input type_ A-phase for the pulse and B-phase for the sign. Show Detail
- No：1366
- Displayed Date：2023/04/25 19:00
When the pulse catch function of the high-speed input module (Type_ NP1X3206-A) is used, can all points be used? Is any difference made to the puls...

Yes, all points can be used. Regarding the pulse width, pulse signals with a width down to 20 us can be captured with ports 1 to 8. With ports 9 to 32, pu... Show Detail
- No：1321
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:17
On the positioning module (Type_NP1F-MP2/MA2), the 'ERR' LED turns ON. What are the possible causes?

A possible cause is that a “Deviation amount over error” occurred. For details, refer to the user's manual FEH213 (NP1F-MA2) or FEH214 (NP1F-MP2) 'Section 8 ... Show Detail
- No：1290
- Displayed Date：2023/04/25 19:00
How do I perform pulse output with the high-speed output module (Type_NP1Y32T09P1-A)?

All the channels in the high-speed output module are set to the general purpose output mode (normal digital output) by default. To use the module in the pul... Show Detail
- No：1613
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:59
In the standard expansion counter FB _MHCNTH, CH0 operates but CH1 does not.

It seems that this problem was caused by an improper address setting for INDAT/OUTDAT assigned to the counter FB terminal. On a single module, assign the sa... Show Detail
- No：1539
- Displayed Date：2023/04/25 19:00
What is the difference in the open-collector pulse input between the high-speed counter (Type_ NP1F-HC2) and the multi-channel counter (Type_ NP1F-...

While NP1F-HC2 requires an external power supply of 5 V DC, NP1F-HC8 produces 5 V DC within the module from an external 24 V DC power supply and does not req... Show Detail
- No：1341
- Displayed Date：2023/04/25 19:00
I used the high-speed counter module (Type_NP1F-HC2) but it doesn't count. I didn't make any settings in particular.

The counter is initially set to gate mode. Counting is disabled unless you provide a 'gate signal' externally by hardware or set 'gate disabled' by software.... Show Detail
- No：1541
- Displayed Date：2023/04/25 19:00
I use the pulse train output positioning control module (Type_ NP1F-HP2). Please tell me the rated voltage/current of the pulse output and control ...

Both the pulse output and control output are open collector outputs. They should be used within the following ranges (1) Pulse output_ 30 V DC, 40 mA or less... Show Detail
- No：1602
- Displayed Date：2023/04/25 19:00