The product type without 'RI' judges ON/OFF of the inputs by current. On the other hand, the product type with 'RI' jud

In a redundant system, both CPUs are identified as CPU0 and you cannot read a battery error of the standby CPU. Determin

The input/output data continue to be valid after the CPU is switched. (The previous values are retained.)

Set the I/O area of the positioning module following the steps below. 1) Set 'h1C00' in the offset word address +16 (Ch1

When the common memory system is used, this can be achieved by handshaking with an application using part of the link me

This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of

The MICREX-SX does not include a communication module having interfaces with Mitsubishi's original networks, MELSEC-NET/

This problem is probably caused by the following reasons: [For SPH300/2000/3000 series] 1) The CPU mode selection switc

You can connect an SX series CPU to D300win via USB, Ethernet or a dedicated loader cable, depending on the model. Confi

Check the following system memory. (1) Configuration information %MW10.52 to %MW10.67 (WSM52 to 67) (2) Configuratio

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

21-30 of Total 235

≪ 3 / 24page ≫

There are two types of AC input modules, for 100V (NP1X1610, NP1X1610-RI) and 200V (NP1X1611, NP1X1611-RI). What is the difference between the prod...

The product type without 'RI' judges ON/OFF of the inputs by current. On the other hand, the product type with 'RI' judges ON/OFF of the inputs by voltage. ... Show Detail
- No：1650
- Displayed Date：2023/04/25 19:00
- Category： I/O
An address error occurs when I read a battery error of the standby CPU (CPU1) from the operating CPU (CPU0).

In a redundant system, both CPUs are identified as CPU0 and you cannot read a battery error of the standby CPU. Determine the condition of the standby CPU fr... Show Detail
- No：1572
- Displayed Date：2023/04/25 19:00
- Category： Application
In a redundant system, are the previous values retained for the SX bus and T-link outputs when the CPU is switched?

The input/output data continue to be valid after the CPU is switched. (The previous values are retained.) Show Detail
- No：1408
- Displayed Date：2023/04/25 19:00
- Category： Application
How do I use a manual pulse generator with the positioning module (Type_NP1F-MP2/MA2)?

Set the I/O area of the positioning module following the steps below. 1) Set 'h1C00' in the offset word address +16 (Ch1 Set value area: Low word). (Set ... Show Detail
- No：1396
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:17
- Category： Function
With the FL-net module (NP1L-FL1/FL2/FL3), is there any way to confirm that the data sent from the node-A have actually been received by the node-B?

When the common memory system is used, this can be achieved by handshaking with an application using part of the link memory. Without handshaking, it is not... Show Detail
- No：1638
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
Although the LED for ±OT lights up on the positioning control module (Type_ NP1F-MP2/MA2), the positioning operation finishes. What is the causal f...

This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of the positioning control module (Type_... Show Detail
- No：1575
- Displayed Date：2023/04/25 19:00
- Category： Function
Is it possible to establish direct communication between Fuji Electric's PLCs and the original networks of Mitsubishi sequencers (MELSEC), NET/B, N...

The MICREX-SX does not include a communication module having interfaces with Mitsubishi's original networks, MELSEC-NET/B or NET/10 or CC-LINK. Alternativel... Show Detail
- No：1546
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I cannot download a project to the user ROM card inserted in the CPU. What is a possible cause?

This problem is probably caused by the following reasons: [For SPH300/2000/3000 series] 1) The CPU mode selection switch is not set at the 'UROM-TERM' pos... Show Detail
- No：1528
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:47
- Category： Support tool
I would like to read and write data by the SX-Programmer Expert (D300win). How do I configure the communication settings for SPH series CPUs?

You can connect an SX series CPU to D300win via USB, Ethernet or a dedicated loader cable, depending on the model. Configure the communication settings acco... Show Detail
- No：1509
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:41
- Category： Support tool (D300win)
I use the hot plug base board with station No. setup function (Type_NP1BS-13D). When I remove a module, how can I identify the removed module in D3...

Check the following system memory. (1) Configuration information %MW10.52 to %MW10.67 (WSM52 to 67) (2) Configuration fault information %MW10.68 to %MW1... Show Detail
- No：1482
- Displayed Date：2023/04/25 19:00
- Category： Main unit

21-30 of Total 235

SPH

I/O
Error

Support tool

Info & News

To Top of Page

PKSHA FAQ logo

SPH

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability