The range in terms of description is up to 4096 words respectively. Note, however, that actual message transfer on the S

Up to 4 units can be connected in 1 configuration (on 1 SX bus). Note, however, that they must be configured so that th

UI4 is not supported by the specification with the VB automation interface. Meanwhile, UI4 is supported by the custom in

It is possible by preparing two types of power supply for driving the transistor device and the load. Refer to the User

While 'DTR_ terminal ready' can be used with RS-232C, this control line is not present for RS-485. If no response is re

With FL-net, Class C IP addresses are used. The range of Class C IP addresses is 192.0.0.* to 233.255.255.*. (Range of

The flashing of the LED of the high-speed output module (Type_ NP1Y32T09P1-A) indicates that pulse output is generated.

The cable is not oil resistant so that you need to protect it by covering it with oil-resistant material.

The influence of external resistance on the thermocouple input is approximately 0.3 ?V/?. The measurement accuracy of t

It occurs when any of the overrun, parity and framing errors is detected in the serial port of a general-purpose communi

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

221-230 of Total 235

≪ 23 / 24page ≫

What is the transfer data size range for the READ_WORD/WRITE_WORD FB?

The range in terms of description is up to 4096 words respectively. Note, however, that actual message transfer on the SX bus takes place after division into... Show Detail
- No：1410
- Displayed Date：2023/04/25 19:00
- Category： Application
How many units of Ethernet module (Type_ NP1L-ET□) can be used in a system?

Up to 4 units can be connected in 1 configuration (on 1 SX bus). Note, however, that they must be configured so that the total number of units of other comm... Show Detail
- No：1395
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
Is communication possible with the UI4 type not supported based on the manual description of the SX communication middleware (Type_ NP4N-MDLW)?

UI4 is not supported by the specification with the VB automation interface. Meanwhile, UI4 is supported by the custom interface specification. Show Detail
- No：1381
- Displayed Date：2023/04/25 19:00
- Category： Support tool
Is it possible to use a transistor output module (12 to 24 V DC model) of the SPH Series at a load voltage lower than the rated voltage?

It is possible by preparing two types of power supply for driving the transistor device and the load. Refer to the User's Guide, which provides explanatio... Show Detail
- No：1331
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:32
- Category： I/O
With communication using RS-485 of a general-purpose communication module (Type_ NP1L-RS□), is there any means to detect a line disconnection?

While 'DTR_ terminal ready' can be used with RS-232C, this control line is not present for RS-485. If no response is received while data are exchanged, re... Show Detail
- No：1322
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:20
- Category： Communication (Others)
What is the range of IP addresses that can be used for FL-net?

With FL-net, Class C IP addresses are used. The range of Class C IP addresses is 192.0.0.* to 233.255.255.*. (Range of *_ 1 to 254) Show Detail
- No：1301
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:19
- Category： Communication (Others)
With the high-speed output module (Type_ NP1Y32T09P1-A), the LED flashes but no pulse is output to the outside. What should I check?

The flashing of the LED of the high-speed output module (Type_ NP1Y32T09P1-A) indicates that pulse output is generated. If no pulse output is generated in t... Show Detail
- No：1291
- Displayed Date：2023/04/25 19:00
- Category： Function
Is the SX bus cable oil resistant?

The cable is not oil resistant so that you need to protect it by covering it with oil-resistant material. Show Detail
- No：1604
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
Is the measurement accuracy affected when an external arrestor for protection is mounted on the input terminal of the thermocouple input module (Ty...

The influence of external resistance on the thermocouple input is approximately 0.3 ?V/?. The measurement accuracy of the thermocouple input is affected by... Show Detail
- No：1545
- Displayed Date：2023/04/25 19:00
- Category： I/O
With the general-purpose communication module (Type_ NP1L-RS□), in what cases does 'C0_ Hardware error detected during receiving' occur?

It occurs when any of the overrun, parity and framing errors is detected in the serial port of a general-purpose communication module. Show Detail
- No：1328
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)