-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
It might be counting noise as a pulse. Take the following measures_ (1) Isolate the pulse generator and PLC from the noise source and shorten the wiring dist... Show Detail
- No：1427
- Displayed Date：2023/04/25 19:00
- Category： Function
-
When the site environment is unfavorable, you are recommended to use the dedicated loader cable. Version V3.2.0.0 or later or V2.2.6.0 or later of D300win ... Show Detail
- No：1423
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
Check the feedback pulse wiring (to make sure that a shielded twisted pair is used, wiring conditions are appropriate, etc.). One possible reason for the c... Show Detail
- No：1421
- Displayed Date：2023/04/25 19:00
- Category： Function
-
Yes, it is generally possible. However, be sure to use compensating leads also for wiring to the recorder. Some recorders may not permit connection dependi... Show Detail
- No：1420
- Displayed Date：2023/04/25 19:00
- Category： I/O
-
When SX-Programmer Expert (D300win) was upgraded to V3.3.2.0, the 'IP address and gateway setting definition' was added to accommodate the function addition ... Show Detail
- No：1417
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
Yes, there are. When you install an expansion FB, sample programs are installed as compressed projects (extension *.Zwt) in a folder named 'Zipped' under t... Show Detail
- No：1414
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
With a general-purpose communication module, is RS232C completely full duplex?
It is full duplex for both hardware and software (firmware) for anything other than communication by M_RECEIVE and M_SEND on the SX bus, which are FB interna... Show Detail
- No：1413
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
For what application is the base board with station number setting switch used?
It is used as a base specified for 'system fail-soft start-up' operation, which is set when there is any base with some modules on which power is not turned ... Show Detail
- No：1411
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
The input/output data continue to be valid after the CPU is switched. (The previous values are retained.) Show Detail
- No：1408
- Displayed Date：2023/04/25 19:00
- Category： Application
-
Is it possible to indirectly specify the timer set value with the Standard Loader (Type_ NP4H-SWN)?
Yes, it is possible. Input a memory address (DLxx) instead of an immediate value as the operand of the timer instruction. Show Detail
- No：1407
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
341-350 of Total 398