Check the feedback pulse wiring (to make sure that a shielded twisted pair is used, wiring conditions are appropriate, e

It is full duplex for both hardware and software (firmware) for anything other than communication by M_RECEIVE and M_SEN

The quotient of a division of the INT or DINT type is rounded down. Accordingly, convert it into the REAL type, perform

It is the same as the loader mode (mode switch 3) of the general-purpose communication module (Type_ NP1L-RS1/RS2/RS3/RS

The current value of the timer can be changed. Note, however, that a circuit for changing the current value of the time

Use the recommended shielded twisted pair cable mentioned in the User's Manual. Also provide shielding.

With the SPH Series, the memory boundaries between the non-retain, retain, system FB and user FB memory areas can be cha

When the P-link module is specified as 'unimplemented' and no P-link module exists in the system, attempting to access t

If battery-less operation is enabled under the 'CPU running definition' setting, the content of the retain memory is not

Create one project file. There are separate tasks for the respective CPUs and the assignment of POUs to tasks determine

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC

Latest FAQ

I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

291-300 of Total 398

≪ 30 / 40page ≫

The current feedback value of the positioning control module (Type_ NP1F-MP2) changes even when the CPU module (Type_ NP1P*-***) is stopped. What c...

Check the feedback pulse wiring (to make sure that a shielded twisted pair is used, wiring conditions are appropriate, etc.). One possible reason for the c... Show Detail
- No：1421
- Displayed Date：2023/04/25 19:00
- Category： Function
With a general-purpose communication module, is RS232C completely full duplex?

It is full duplex for both hardware and software (firmware) for anything other than communication by M_RECEIVE and M_SEND on the SX bus, which are FB interna... Show Detail
- No：1413
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
How can I round the result of a division with D300win?

The quotient of a division of the INT or DINT type is rounded down. Accordingly, convert it into the REAL type, perform the division as the REAL type and con... Show Detail
- No：1412
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
What is the communication protocol for the loader port of the CPU module of the MICREX-SX SPH Series?

It is the same as the loader mode (mode switch 3) of the general-purpose communication module (Type_ NP1L-RS1/RS2/RS3/RS4/RS5). Show Detail
- No：1379
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
With a project created by using D300win, is it possible to change the current value of the timer? If so, how can I change the value?

The current value of the timer can be changed. Note, however, that a circuit for changing the current value of the timer must be added. Show Detail
- No：1375
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:44
- Category： Support tool (D300win)
What measures can I take against external noise of the high-speed counter (Type_ NP1F-HC2)?

Use the recommended shielded twisted pair cable mentioned in the User's Manual. Also provide shielding. Show Detail
- No：1365
- Displayed Date：2023/04/25 19:00
- Category： Function
I compiled a project of the SPH Series and came across a memory shortage error. Is there any way to deal with this problem?

With the SPH Series, the memory boundaries between the non-retain, retain, system FB and user FB memory areas can be changed to change the size of the respec... Show Detail
- No：1359
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
In an SPH system, I specified the P-link module as 'unimplemented' and the program execution time was extended. Why?

When the P-link module is specified as 'unimplemented' and no P-link module exists in the system, attempting to access the P-link memory using a contact, coi... Show Detail
- No：1355
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
The variables I specified as retained by using D300win are not retained through a power failure. What can I do to solve the problem?

If battery-less operation is enabled under the 'CPU running definition' setting, the content of the retain memory is not retained. Disable battery-less opera... Show Detail
- No：1350
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:36
- Category： Support tool (D300win)
The SPH300EX (Type_ NP1PS-74D) integrates two CPUs. Do I need to create separate project files for the respective CPUs?

Create one project file. There are separate tasks for the respective CPUs and the assignment of POUs to tasks determines the CPU to which the program is a... Show Detail
- No：1330
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:32
- Category： Support tool (D300win)